There is usually a moment when a problem stops being something to keep an eye on and becomes something to call about. A breaker that trips again after you reset it. An outlet that stopped working for no reason you can find. A panel that buzzes faintly at the end of a long day. Those are the calls we get from Covington regularly, and each one gets a proper look before any work is recommended.
Covington's housing stock covers a wide range, from older brick homes on original wiring to newer construction and rental properties managed by people who need reliable work done without a lot of back and forth. Whatever the property type, the process is the same: describe what you are seeing, get a price before anything is scheduled, and know what the visit will cover before anyone shows up. That is how we work. Every job gets treated like it matters, because it does.
Call (513) 669-9289 to get started.
A dead outlet is not always a simple swap. Before anything is replaced, we check what is behind it, because the outlet is often where a wiring fault or an overloaded circuit shows up rather than where it starts. We install standard outlets, GFCI outlets in kitchens and bathrooms, AFCI protection where the circuit calls for it, and exterior weatherproof outlets for garages and back porches. Switch replacements, dimmer installations, and smart switch wiring all fall in the same category. If the existing wiring does not support what the switch needs, we say so before we start.
An appliance that shares a circuit with other loads is a common source of nuisance tripping, and the fix is usually a dedicated circuit sized for the appliance rather than a panel adjustment. We run dedicated circuits for dryers, ranges, dishwashers, refrigerators, and any 240-volt equipment that needs its own path. Hot tub hookups and workshop subpanels follow the same logic: the load gets its own circuit, the panel gets checked for capacity before anything is run, and a load calculation confirms the service can carry what is being added.
Properties outside the city's core, and some within it, carry well pump circuits or irrigation systems that need their own dedicated wiring. These circuits run at specific voltages and amperages that have to match the pump or controller, and a wiring fault on one of them can take out the pump without touching anything else in the house. We scope these jobs carefully on the call so the circuit is sized and wired correctly from the start.
A plug-in power strip handles what is plugged into it. It does not protect the panel, hardwired appliances, or circuits in other rooms. A panel-mounted surge protector installs at the point where power enters the home and absorbs voltage spikes before they reach the wiring. In a region where summer thunderstorms and utility fluctuations are a regular occurrence, that kind of protection covers the whole electrical system in a way that individual strips cannot. We install whole-home surge protection as a standalone job or as part of a panel upgrade.
Older homes frequently have grounding and bonding issues that were acceptable under the code in effect when the home was built but do not meet current standards. Ungrounded two-prong outlets, missing ground wires in junction boxes, and bonding gaps at water and gas lines are all things we find and correct. These are not cosmetic fixes. Proper grounding is what allows a circuit breaker or GFCI to do its job when something goes wrong. We check the grounding and bonding as part of any safety inspection and address it as a standalone job when a homeowner or property manager already knows it needs attention.
Covington has a mix of properties, and the panels in them reflect that. Some homes still carry panels that were sized for a much lighter load than the household now places on them. A panel that was adequate when the home was built may now be running central air, a home office, an electric vehicle charger, and a full kitchen at once. That combination adds up, and a panel that cannot carry it will show the strain through tripping breakers, warm breaker covers, or simply running out of open slots.
When we assess a panel, we look at the service entrance, the breaker condition, the grounding, and whether the rated capacity matches the actual load. For older homes in Kenton County, a move to 200-amp service is often the right answer, particularly if the property is going through a renovation or adding significant new circuits. Subpanel installation is an option when a garage, finished basement, or addition needs its own circuit group without running everything back to the main panel.
We also handle backup generator hookups on the electrical side: the transfer switch, the wiring from the generator to the panel, and the interlock that keeps utility power and generator power from feeding the same circuit at the same time. The generator unit is a separate purchase. We work with what the customer has chosen and make sure the electrical installation is done correctly.
When a job is finished, the work does not end at the last connection. Circuits get labeled at the panel so the next person who opens it knows what goes where. Wiring that was run through walls or ceilings is documented so a future contractor or inspector is not guessing. GFCI and AFCI outlets are tested before we leave. For safety inspections, a written summary of what was checked, what was found, and what was corrected is part of what the customer gets.
That documentation matters more than it might seem. A property being sold or rented again needs to show that the electrical system is in known condition. A buyer's inspector will ask about the panel, the grounding, and whether the wiring has been updated. Having clear records of what was done and when makes that conversation straightforward rather than uncertain.
Ceiling fan installations, recessed and LED lighting work, and appliance circuit additions are all completed the same way: tested, labeled, and cleaned up before we leave. No-pressure estimates, priced up front, so you know what the job covers before anyone shows up. There is more on our wiring and panel services page.
Not every electrical problem starts inside the home. When part of the house loses power and the breaker appears fine, or when voltage is inconsistent across circuits, the fault may sit at the service entrance or on the utility's side of the meter. We check the service entrance and the panel first to determine where the fault is.
If the problem turns out to be on the utility's side, we tell you that and explain what to report to the utility company. We do not do the utility's work for them, but we make sure you know what you are dealing with and what the next step is. If the fault is on our side, we scope the repair and give you a price before anything is touched.
Most electrical work gets scheduled in advance. Some of it does not. A burning smell near the panel, sparks from an outlet, or a breaker that will not stay reset are not situations to leave until a convenient time opens up. We take short-notice calls, so reach out and ask what the schedule allows. Ask what the schedule allows when you call and we will tell you what we can do.
For rental properties and businesses that need to stay open, we work around the situation. That means confirming what needs to be shut down and for how long before the visit, and scoping the work so the disruption is as short as it can be. Tenants get advance notice of what to expect, and property managers get a clear account of what was done. Clear communication from the first call to the final test is how every job gets handled.
One call. One electrician. One price, agreed first.
The price for electrical work depends on what the job involves at the specific property. A ceiling fan installation in a room with existing wiring and a properly rated box is a different job from the same fan in a room where no overhead circuit exists. A panel upgrade in a home with a straightforward service entrance is different from one where the entrance needs work before the panel can be replaced. What the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change are the things that move a price.
When you call, we ask the right questions to understand the scope before giving a number. You get the price on the phone or, for jobs that need a site look, before any work begins. Nothing is scheduled until the price and the scope are agreed. Call us and we'll walk you through the fix.
We take calls from across Kenton County, including Kenton Vale, Fort Wright, Fort Mitchell, Wilder, and Taylor Mill.
If you are in or near Covington and need electrical work handled, call (513) 669-9289 and describe what you are seeing.
Yes. We work with landlords and property managers across Kenton County on outlet replacements, panel work, lighting, dedicated circuits, and safety inspections for units between tenants. The process is the same as for any other property: the scope is established on the call, the price is confirmed before scheduling, and the work is completed with as little disruption to tenants as the job allows.
Homes in Covington frequently have panels that have not been updated since the home was built, ungrounded two-prong outlets, and wiring that predates current GFCI and AFCI requirements. Grounding and bonding corrections, panel upgrades, and outlet replacements are among the most common calls we get from properties in this area. If you are not sure what your home has, an electrical safety inspection gives you a clear picture before any work is committed to.
The main difference is that the supply may be shared or metered separately for each unit, and the panel for one unit may be in a common area rather than inside the unit itself. We confirm the supply arrangement on the call and plan the work accordingly, including any coordination needed with building management to access a shared panel or common area.
It depends on the condition, the wiring type, and whether the installation meets current code. We assess what is there before committing to reusing it. If the existing outdoor wiring is not suitable, we explain why and scope a replacement.
Partial power loss that follows no obvious single circuit pattern often points to a problem at the service entrance or at the panel, rather than a fault on a branch circuit. A common cause is the loss of one leg of the 240-volt supply, which takes out circuits on that leg while leaving others live. This is worth calling about promptly.
Describe the problem on the call and we will tell you what the work likely involves and what it will cost before anything is scheduled. We are available every day from 5:30 AM to 9:00 PM.
Call (513) 669-9289.
By the end of that call, you will know what the job covers, what it costs, and when it can be done.
The rest are on our local coverage area. Also serving the towns around: Norwood, Anderson Township, Green Township, Reading, Springfield Township.
Below is a plain-language look at the electrical work we handle in Covington and across Kenton County. Each row covers what the service includes, who it fits best, and a practical note worth knowing before you call. If a job you need is not listed, describe it when you call and we will tell you what it involves and what it will cost.
| Service Type | What It Covers | When You Need It | Things to Know |
|---|---|---|---|
| Breaker & Fuse Repair | Breakers that trip repeatedly, Breakers that will not reset, Warm or buzzing panels, Fuse panel assessment | Any property where a circuit keeps going out under normal load | A breaker that trips repeatedly is telling you something about the circuit, not just the breaker. We check both before recommending a fix. |
| Ceiling Fan Installation | Fan-rated box installation, New circuit runs where needed, Wall control and switch wiring, Replacement of existing fans | Rooms without existing fan wiring or with a light box not rated for fan weight | A standard light box is not rated to support a ceiling fan. We install the correct box and run the circuit if one is not already in place. |
| Electrical Panel & Service Upgrades | 100 to 200 amp service upgrades, Subpanel installation, Load calculation and assessment, Code violation corrections | Older homes adding appliances, EV chargers, or finishing new living space | Most mid-century homes in this area were built with 60 or 100 amp service. A full renovation or a new high-draw appliance often makes a panel upgrade the right starting point. |
Call (513) 669-9289 to describe the job and get a price before you commit to anything. We are available every day from 5:30 AM to 9:00 PM.
(513) 669-9289